Runlic IoT Kit

Runlinc

• Runlinc IDE is simple and easy, the ON/OFF button can control anything, anywhere, in only two lines of code compared to more than 120 lines on Arduino

• Runlinc IDE is faster than other technologies, the buzzer and the Runlinc engine need only 30 minutes to turn on and off the LEDs compared to 30 hours for a web server

Note: please do not remove the yellow sticker on the NodeMCU-ESP32 chip as you will need the number on the chip to configure the chip connection in the Runlinc web page that is used to program the chip.

Note: DO NOT upload any code Arduino to the NodeMCU-ESP32. The Runlinc IDE configuration inside the Wi-Fi chip is not replaceable!

Features

NodeMCU-ESP32:

• NodeMCU based on ESP-WROOM-32 module

• Based on ESP32 DEVKIT

• 30-pin GPIO version

• 32-bit dual-core processor with integrated 2.4 GHz Wi-Fi and Bluetooth

• 4 MB flash memory

• 520 KB RAM

• 2.2 to 3.6 V Operating voltage range

• USB micro B for power and serial communication, to be used for program loading and serial debugging as well

STEMSEL E32W:

• 4-port embedded driver for 2 forward/reverse motors or 4 motors in 1 direction, can also be used for small lamps, relays, etc. (up to 500 mA)

• Driver can be enabled or disabled to use ports and inputs, etc.

• The driver can produce voltage on the "12V" input so that it can drive 12V, etc. on the driver outputs

• 6 x servo motor connectors with power connection directly from "Vin" input to drive high current servo motors at 6V, etc. (runlinc software directly supports servo motors)

• On-board regulator so that the board can operate on a 5 to 15 V supply. (including 6V, 9V, 12V, etc.)

• Has 3-pin connectors for direct connection of I/O sensor or output devices without additional wires required for 3-pin devices.

• Dimensions: 60 mm x 73 mm

Contents of the kit

• STEMSEL E32W board

• ESP32 Wi-fi NodeMCU module

• 1 x USB Micro B cable

• 40 x male to female connecting wire

• runlinc IDE ( pre-installed in the NodeMCU ESP32)

• 37 in 1 sensor kit

• • Analog joystick 1 x 2 axes
  • 1 x relay
  • 1 x microphone for audio detection of loud noises
  • 1 x microphone for audio detection of small noises
  • 1 x small IR sensor for tracking
  • 1 x IR sensor for avoidance and detection
  • 1 x Flame
  • 1 x linear hall sensor for detecting magnetism
  • 1 x touch sensor
  • 1 x digital temperature sensor
  • 1 x active buzzer, audio output
  • 1 x passive buzzer, Piezo buzzer
  • 1 x RGB LED, through-beam LED
  • 1 x SMD RGB, SMD LED
  • 1 x Two-color LED
  • 1 x Mini two-tone
  • 1 x Reed switch
  • 1 x Mini reed switch
  • 1 x Heartbeat
  • 1 x 7 color flash, LED auto flash
  • 1 x Laser transmitter
  • 1 x Button, push button
  • 1 x Shock
  • 1 x Rotary encoders
  • 2 x Light cutting module
  • 1 x Ball switch
  • 1 x Rocker switch, mercury
  • 1 x Photoresistor, LDR
  • 1 x Temperature and humidity sensor
  • 1 x Analog channel
  • 1 x Magnetic channel
  • 1 x 18B20 temperature
  • 1 x Analog temperature sensor, thermistor
  • 1 x IR transmitter
  • 1 x Infrared receiver
  • 1 x Valve module
  • 1 x Light blocking

Resources

• Installation Guide for STEMSEL E32W V1.0
• Pin configurations for ESP-WROOM-32 and STEMSEL E32W boards
• Runlinc main site

Tutorials :

• Beginner projects
  • Alarm system
  • Smart light
  • Refrigerator Alarm
  • Home automation controls
  • Traffic lights
  • Washing machine
  • Temperature control
• Intermediate projects
  • Define the fire hazard limit
  • Radiation meter
  • Wind power
  • Liquid level sensor
  • Vending machine
  • Combination lock
• AI projects
  • Intrusion alarm
  • AI chat bot
  • AI Image Identification
  • AI Machine Learning
  • AI object recognition library
• Communication projects
  • Telecommunication
  • Binary numbers

Remark: Please note that all these tutorials are NOT based on the 37-in-1 sensor kit. You must prepare your own sensors if they are not included in the sensor kit.