Measure temperature, humidity, atmospheric pressure, carbon dioxide (CO2) concentration and volatile organic gas (VOC) concentration with the on-board BME688 sensor Monitor data with integrated mini OLED display Embedded RP2040 chip for data logging Connect to your Raspberry Pi via GPIO...
NUCLEO-64 development board based on the STM32F411RET6 32 bits ARM Cortex-M4 microcontroller Ideal for industrial use, prototyping,... Arduino UNO R3 and ST Morpho sockets extend the connection functionalities Integrates ST-LINK/V2-1 (programmer/debugger) and complete HAL STM32 software...
IO development board for Raspberry Pi Pico Multiple communication ports: x2 I2C, x2 UART, 2 x SPI, x3 analog I/O and x13 digital I/O 6.5-12 V power supply interface Compatible with Lego extensions
Breakout board with uBLOX MAX-M8Q-10 module and SMA female connector for active antennas Quick start, PPS LED and Supercap included to maintain settings during power cycles Suitable for HAB use with maximum altitude of 50000 meters in flight mode TX, RX, TP (PPS output), 3 V supply (2.7 V to 3.6...
Starter kit with everything you need to get started right out of the box! Includes 5V power supply, USB cable, cooling fan,heat sinks, case and HMDI cable Simply match these accessories to your LattePanda V1 board
Screw-in grove modules, solderless connection Connect your Grove sensors to your board Raspberry Pi or Arduino Ideal for simplified prototyping projects Holds your electronic modules
Wideband (100 MHz to 4 GHz) Low Noise Amplifier Modules (LNA) based on SAW bandpass filter Designed to pass between a software defined radio receiver and an antenna and reduce out-of-band intermodulation while providing additional gain for increased sensitivity Compatible with most...
Mini Base-board to add the Raspberry Pi 4 ports to your Raspberry Pi Compute Module 4 Suitable for testing and using the Raspberry Pi CM4 or to be integrated into finished products thanks to its dimensions similar to those of the Raspberry Pi 4 GPIO Header Raspberry Pi 40PIN Color Coded...
High precision fingerprint sensor with 360° verification Based on a high-performance Cortex processor Compatible with Raspberry Pi and STM32 thanks to the integrated UART connector Capacitive sensitive detection, so verification is done quickly upon touch
Isolated relay HAT card Has one two-channel input and one two-channel output Up to 24V DC or 250V AC at 10A Design makes it easy to connect to cards Arduino
GPS / RTC expansion card with multi-GNSS GPS receiver Featuring PPS output to enable card use on PPS-disciplined NTP servers, and RAW output available from the UBlox™ GPS module Compatible Raspberry Pi (via 2x20 GPIO header) Quick plug-n-play connection and no soldering required
Designed to simplify the Internet of Intelligent Things (AIoT) by integrating the power of ESP32 Offers reliable Wi-Fi and Bluetooth connectivity x3 Ports Maker, compatible with Qwiic, STEMMA QT and Grove Board preloaded with CircuitPython, also compatible with Arduino IDE, MicroPython...
Mini base card with x2 Gigabit Ethernet ports 10/100/1000M compatible Designed for all versions of Compute Module 4 Integrated interfaces: x40 GPIO, USB 2.0, microSD card slot useful for CM4 Lite variants (without eMMC) Connectivity that perfectly meets the specific needs of industrial...
Board with the RP2040 microcontroller chip designed by Raspberry Pi in the UK Embeds a 1.28-inch round LCD display Includes temperature sensor, accelerometer and gyroscope Full SDK, C/C++ and MicroPython support
CAN RS485 isolated extension HAT 1 CAN channel : MCP2515 controller with CAN transceiver 2 RS485 channels: SC16IS752 and SP3485 dual chip combination Standard 40PIN GPIO header Raspberry Pi
Beginner's kit with 10 Grove modules + 1 Grove Base Shield on a single PCB Ideal for beginners to learn programming and discover the electronic possibilities Designed specifically for use with theArduino UNO (not included) Easy connection of modules in Plug & Play, without...
Uninterruptible Power Supply (UPS) card to power your Raspberry Pi Compute Module 4 Enjoy stable, uninterrupted power Designed to allow you to work for long hours on your project with long battery life Offers a wide range of connectivity: x40 PIN GPIO, x4 USB, Gigabit Ethernet, x2 HDMI, M.2 M...
4x8 LED Matrix Module SK6812 Compatible with micro:bit, just clip your card into the shield The three primary colors of each pixel can realize 256 levels of brightness display, up to 16777216 types of colors: it is the assurance of brilliant and bright colors! Embedded x2 3.3V...
Breakout board with uBLOX MAX-M8C-1 module with additional power filtering, chip antenna and decoupling capacitor Light weight of only 1.5g Suitable for HAB use with maximum altitude of 50000 meters in flight mode VCC, GND and RX & TX, SCL & SDA for I2C
Grove plug-and-play display Displays up to 32 characters, with support for English, Japanese and Greek alphabets Compatible with Arduino and Raspberry Pi Ideal for displaying temperature or time, or any other project requiring a simple display
Have a fun and creative learning experience with LEGO® and Raspberry Pi Raspberry Pi Build HAT add-on board with a Raspberry Pi RP2040 microcontroller designed in collaboration with LEGO® Education and compatible with all LEGO® models Raspberry Pi Control up to 4 LEGO® extensions such as...
Fast and stable capacitive fingerprint module with dcommunication port, UART or USB Includes a high-performance Cortex core processor, a high-security commercial fingerprint algorithm and an advanced solid-state fingerprint sensor Éequipped with fingerprint enrollment, image processing, pattern...
Geekservo 2kg 360° servo motor Suitable for medium and large projects Compatible with lego Dual 360° output axes
Designed specifically for Raspberry Pi 4B / 3B+ and Nespi Case+ compatible Dual fans with high-speed, low-noise cooling Reduces temperature by up to 20°C Heat sinks and ribbons included
Français
Español
Italiano
Deutsch
