Looking for USB and Ethernet ports for your Raspberry Pi Zero 2 W board? The USB/LAN module is the answer! Clips onto the underside of the ARGON POD case, connecting via an exposed header to the USB/HDMI module Provides x4 additional USB ports (two on the front and two on the rear)...
Combined 2.4 GHz and 5.8 GHz dual-band Wi-Fi and Bluetooth module Works with the ODROID series and is Android and Linux compatible Realtek RTL8821CU chipset Transfer speed ~200 Mbps
Breakout board with uBLOX MAX-M8Q-10 module and SMA female connector for active antennas Quick start, PPS LED and Supercap included to maintain settings during power cycles Suitable for HAB use with maximum altitude of 50000 meters in flight mode TX, RX, TP (PPS output), 3 V supply (2.7 V to 3.6...
Wideband (100 MHz to 4 GHz) Low Noise Amplifier Modules (LNA) based on SAW bandpass filter Designed to pass between a software defined radio receiver and an antenna and reduce out-of-band intermodulation while providing additional gain for increased sensitivity Compatible with most...
Breakout board with uBLOX MAX-M8C-1 module with additional power filtering, chip antenna and decoupling capacitor Light weight of only 1.5g Suitable for HAB use with maximum altitude of 50000 meters in flight mode VCC, GND and RX & TX, SCL & SDA for I2C
Flirc allows you to pair any remote with your computer or media center. Just browse our super-simple cross-platform pairing application, and you're done. Use your previously paired remote without additional software on any flirc-enabled machine.
Low Noise Amplifier Modules (LNA) based on SAW bandpass filter Designed to pass between a software defined radio receiver and an antenna and reduce out-of-band intermodulation while providing additional gain for increased sensitivity Compatible with most USB SDR dongles such as RTL...
Adapter with NRF24L01+ module A practical solution for quick and efficient integration of wireless communication into your projects Supplied with pre-soldered connectors, simply plug the adapter into your Dasduino board Dimensions: 38 x 22 mm
Official antenna Raspberry Pi certified compatible for the Compute Module 4 Allows to increase the reception range of a Wi-Fi signal Stabilizes and limits the loss of Wi-Fi data rates Includes a bracket and a connection cable for the antenna
The Arduino card is the basis for creating secure WiFi and Bluetooth® applications.
With this miniature wifi module, free your Internet projects from network cables by adding a wifi module! Your Raspberry is equipped with a USB port, so you can have a reliable wireless Internet connection at an affordable price. You will have a wireless Internet connection in 10 minutes! Works...
Compatible with Raspberry Pi A, B, A+, B+, Zero, 2, 3 with its L80-39 GPS chipCommunicates satellite data via UART or USBCP2102 as a stable and faster UART chip USB bridge66 simultaneous search channels and 22 tracking channelsAdvanced AGPS EASY™ technology without external memory USB cable not...
This ADS1015 ADC (analog-to-digital converter) package has three channels that can read voltages from -24 V to +24 V at sampling rates up to 3.3 KHz with 12-bit resolution. It is compatible with Raspberry Pi and Arduino and is ideal for measuring voltages quickly and accurately over a wide...
The RemotePi card is an infrared remote control with on/off button. This card is mainly unitlised on a media center or emulator, LibreELEC, OpenELEC, OSMC, XBian, RasPlex, Raspbian, Volumio, RetroPie, Recalbox ... This infrared remote control will allow you to navigate through the menus of your...
The SIM7020E is a NarrowBand-Internet of Things (NB-IoT) module specifically designed for the Raspberry Pi Pico and is ideal for IoT applications Supports multiple NB-IoT frequency bands, UART communication, serial AT command control, support for multiple communication protocols, support for...
GSM antenna (850/900/1800/1900 MHz) which can be attached to the board with the micro UFL connector. Suitable for MKRFOX1200, MKR WAN and MKR GSM.
Français
Español
Italiano
Deutsch
