3.97" color touchscreen with up to 5 simultaneous touch points and 800 x 480 pixel resolution Add a graphical interface to your projects, with easy connection via J5 and J6 headers Embeds a digital microphone, accelerometer/gyroscope circuit, etc. Compatible with 20-pin DVP cameras...
5050 RGB LED strip light (3m), which offers programmable light colors Each LED is controllable by an independent I2C IC Double-sided adhesive tape on the back side, to easily attach the LEDs to your surfaces IP65 protection rating, with transparent resin layer for protection against small...
16x32 LED Panel Tropicalization and Waterproof P10 for outdoor use Red monochrome color Ideal for displaying text and animations
4x8 LED Matrix Module SK6812 Compatible with micro:bit, just clip your card into the shield The three primary colors of each pixel can realize 256 levels of brightness display, up to 16777216 types of colors: it is the assurance of brilliant and bright colors! Embedded x2 3.3V regulators,...
Create a unique electronic die with bright LEDs and customize your die by choosing from a variety of LED colors included in the kit Learn the basics of soldering and electronics while having fun! The kit is ideal for beginners who want to learn practical skills Integrated Attiny404...
Illuminated 1.2" high display module with 4 high-quality 7-segment displays Combined with a display, it offers exceptional legibility even in bright environments Ideal for displaying digital clocks, timers, counters, scoreboards, etc. Each module has a DIP switch for configuring the I2C...
16x7 LED array (112 RGB LEDs) with individual color/brightness control of each LED Resized for Raspberry Pi Pico and programmable in C / C ++ and MicroPython 4 x programmable touch buttons Fully assembled, pre-welded epre-welded female bases for attachment to the Pico and no soldering required...
8x8 LED matrix display based on chip HT16K33 Simply use the I2C port of your microcontroller to control the dot matrix Address setting via switch Wire connection via jumper cable
Honeycomb-shaped digital LED module Red color LED x6 annotated ports for easy operation Compatible with micro:bit card (alligator clip connection)
Module composed of 8 programmable RGB lights Compatible Arduino, Micro:bit and Raspberry Pi Pico 3 possible connection methods: alligator clip, Dupont cable and PH 2.0 cable High brightness (256 brightness levels) - ideal for creating lighting effects
The Arduino MKR RGB Shield puts 84 LEDs (12x7) at your service! Write messages and add graphics with this shield Very dense and bright LEDs with full RGB colors No need for soldering or adapters, just plug the RGB Shield into your favorite MKR board
2048 RGB 64x32 LED array with 2.5mm spacing Compatible with Arduino Mega, Raspberry Pi Possibility to connect several panels together (program not supported by Arduino) PCB with two IDC connectors on the back and 12 16-bit locks that allow you to drive the display with a scan rate of 1:16
7x17 LED array (119 white LEDs) with individual brightness control of each LED Compatible with Raspberry Pi Pico and programmable in C / C ++ and MicroPython 4 x programmable touch buttons and IS31FL3731 LED array driver chip Fully assembled, pre-soldered female sockets for attachment to the Pico...
The bit: LAMP has connections that allow the microbit to be bolted/clipped directly onto it. It was designed to replicate a street light, in form and function. This board is ideal for transportation projects and has been designed to match the same aesthetic as STOP: bit, so they can be used...
only one module can drive an 8x8 dot common cathode array Operating voltage: 5V Module size: 12.8 x 3.2 x 1.3 cm (l * w * h) with 64 screw mounting holes, hole diameter: 3mm module with input and output interfaces, support multiple modules in cascade
A tiny compact array of 77 individually controllable bright white LEDs. Ideal for scrolling text, animations, bar graphs or just general lighting, it is compatible with Raspberry Pi and Arduino.
This super cute 5x5 RGB LED matrix board is a great way to visualize sensor data or for simple animations or notifications, and is compatible with Raspberry Pi and Arduino. These small arrays are great for viewing data from other boards in a Breakout Garden HAT, such as the environmental data...
ACCESS: bit is a bolt-on/clip-on card for the BBC microbit that simulates an access gate. It includes a switch to turn on and off the built-in 3xAAA battery power, as well as an audible horn. The ACCESS: bit joins the micro: bit family of transport / crosswalk accessories, which also includes;...
16 x 10 RGB LED array designed for Raspberry Pi Pico Equipped with 160 constant current RGB LEDs with IC quality controller and LED chip IC controller with high reliability, high anti-interference performance, high constant current accuracy and low power consumption Programmable with C/C++ and...
Acrylic sheet with black LED diffuser, size 12" x 12" and thickness 0.1" (2.6 mm) Perfect for use in a variety of lighting projects, ideal for glossy projects, matrices and NeoPixels,... Thanks to its high diffusion properties, it distributes the light emitted by the LEDs evenly, avoiding...
Add some color to your next coding project with our new Halo board for the BBC Micro: bit. The Halo features 24 customizable color addressable ZIP LEDs.
Dual LED matrix (5x7 + decimal point) with retro look Ideal for simultaneous display of two numbers or two letters (countdowns, percentage readings, ...) or a graphic display No soldering required, this breakout board is pre-assembled and includes a LED driver mounted on an I2C breakout and...
Français
Español
Italiano
Deutsch
